Well Pump Services in Lake Stevens, WA
Well homes around Granite Falls and the rural edges of Lake Stevens depend on one pump. When it quits, so does every tap in the house. We diagnose pump, tank, and switch problems — and we will tell you plainly which one failed.
No water on a well system is an emergency with three usual suspects: the pump, the pressure tank, or the controls. Eby Plumbing services well pumps and pressure tanks for homes around Lake Stevens — and one thing to know up front: we service and replace pumps. We do not drill wells, which is a separate licensed trade.
Pump, tank, or switch? How we diagnose
Before assuming the pump is dead, we check the cheap causes first: the breaker, the pressure switch, and the pressure tank's air charge. A tripped breaker or a failed switch looks exactly like a dead pump from inside the house. A waterlogged tank looks like a failing pump too — rapid cycling, pressure swings, air sputtering from faucets. Replacing a pump when the tank killed it just buys you a second dead pump, so diagnosis comes before any quote.
Submersible vs jet pumps
Most drilled wells use submersible pumps, which sit down in the well itself — quiet, efficient, and out of sight. Shallow wells may use jet pumps mounted above ground, either in the house or a pump house. Replacement matches your existing setup; switching types is rarely necessary and never something we recommend without a reason.
Breaker, switch, tank, or pump — in that order of cheap-to-expensive causes.
Almost always a waterlogged pressure tank with no air cushion left.
Tank or switch trouble, or a pump losing capacity.
The pump is drawing air — low water level, tank trouble, or a failing pump.
A short-cycling pump runs far more than it should and shows up on the bill.
Worn pump, a leak in the drop pipe, or the well itself running low.
The pressure tank is the part everyone forgets
The tank's job is to hold an air cushion so the pump runs in long, easy cycles instead of starting every time you open a tap. When the bladder fails or the air charge leaks out, the tank waterlogs: pressure drops instantly, the pump restarts within seconds, and that short-cycling wears the pump out years early. Tank replacement costs far less than pump replacement, which is why we check the tank on every well call.
Well water treatment, while we are there
Many well homes have a second problem hiding behind the first: iron staining, sulfur smell, or hardness. Once the pump and tank are healthy, treatment sized to a water test handles the rest — see our water filtration page for the options.
| Job | Notes |
|---|---|
| Well pump diagnosis | Breaker, switch, tank, and pump tested in order — no guessing |
| Submersible pump replacement | Matched to your well depth and household demand |
| Jet pump service and replacement | Above-ground pumps for shallow wells |
| Pressure tank replacement | The fix for rapid cycling, and the thing that saves the next pump |
| Pressure switch and controls | Switches, gauges, and control boxes |
| Well water treatment | Iron, sulfur, and hardness filtration sized to your water test |
Scope depends on well depth, pump type, and whether the tank or controls also need work — confirmed with a written quote before work begins.
We service pumps. We do not drill wells.
Drilling a new well is a separate licensed trade with its own rigs, permits, and geology. If your well itself has failed — collapsed casing, a dry aquifer, contamination — we will say so plainly and point you to a drilling contractor rather than sell you a pump that cannot fix it.
Iron, sulfur, or hardness?
Once the pump is healthy, treatment handles the water itself. See water filtration & softening.
Old lines from the well to the house
Corroded or undersized supply lines starve the house of pressure. See water lines.
Pressure problems after the tank
House-side pressure issues have their own fix. See pressure regulators.
Last updated: November 2026
November-December in Lake Stevens
Well homes depend entirely on electric pumps, and November and December storms test that dependence. A power cut means no water at all once the pressure tank drains - about 10 to 30 minutes of normal use - and the same outage kills the well-house heater, so the system can freeze during the outage. The 1/4-inch pressure-switch sensing tube chills fastest, and a pump running against a frozen line can overheat and burn out.
The risk starts with the first sub-freezing nights, November 19-21, and rises with each windstorm and power cut after that. The pre-storm check is insulation, heat cable, and a thermostatic heater in the well house, plus a generator or transfer switch - done before the storm, not during it. A generator or transfer switch is electrical work, not plumbing, so arrange one with a licensed electrician; we do not install them. A well pump that runs but never builds pressure, or a pump cycling rapidly, needs diagnosis before the next storm, not after.
Our winter plumbing guide for November-December 2026 has the full timeline, the ranked top 10 pain points, and the winterization checklist.
Frequently asked questions
I have no water at all. Is it the pump?
Not necessarily. Check the breaker and the pressure switch first — both are common, cheap causes. If those are fine and the tank is waterlogged or the pump will not build pressure, the pump is the likely culprit, and we will confirm it with testing before quoting a replacement.
How long does a well pump last?
Most last 8 to 15 years. The biggest factor is the pressure tank: a healthy tank lets the pump run in long, easy cycles, while a waterlogged tank makes it short-cycle and wear out years early.
Why does my pump turn on and off every few seconds?
Almost always a waterlogged pressure tank — the air cushion is gone, so pressure drops instantly and the pump restarts. Replacing the tank usually fixes it; running it that way will kill the pump.
Do you drill wells?
No. Well drilling is a separate licensed trade with its own rigs and permits. We service, repair, and replace pumps, pressure tanks, and controls on existing wells.
My well water stains everything orange. Can you fix that?
That is iron, and it is a treatment problem, not a pump problem. An iron filter sized to your water test handles it — see our water filtration page.
What happens to my well water during a power outage?
You lose water once the pressure tank drains - about 10 to 30 minutes of normal use. The same outage kills the well-house heater, so the system can freeze during the outage. A generator or transfer switch, plus insulation and heat cable in the well house, is the pre-storm answer - arranged before the storm, not during it. A generator or transfer switch is electrical work, not plumbing, so arrange one with a licensed electrician; we do not install them.
Can my well pump freeze in November?
Yes, from the first sub-freezing nights, November 19-21, onward. The 1/4-inch pressure-switch sensing tube chills fastest, and well-house and entry pipes freeze when the well-house heater fails or the power goes out. A pump running against a frozen line can overheat and burn out, so insulation, heat cable, and a thermostatic heater matter before the first freeze.
Can't find your question? Browse all plumbing FAQs.
Need a plumber in Lake Stevens, WA?
Call Eby Plumbing for same-day service across Lake Stevens and surrounding areas.
Call (425) 380-0034