Fixture Repair & Installation in Lake Stevens, WA
A running toilet can waste thousands of gallons a year. A dripping faucet keeps you up at night. Most fixture problems are small jobs — and we will tell you honestly when a repair beats a replacement, and when it does not.
Fixtures are the plumbing you touch every day, so when one fails it is personal. Eby Plumbing repairs and replaces toilets, faucets, sinks, showers, and tubs across Lake Stevens — and gives you a straight answer on whether the old one is worth saving.
Toilets: running, rocking, and replacement
A running toilet is usually a worn flapper letting water leak from tank to bowl, or a fill valve set too high — both inexpensive repairs. A rocking toilet is different: it means the wax ring seal has failed or the flange underneath is damaged, and a slow leak at the base rots the floor while you ignore it. Replacement makes sense when the bowl is cracked, the toilet clogs constantly, or it is a pre-1994 model using 3.5 gallons or more per flush — a modern 1.28-gallon toilet uses far less water and flushes better than the early low-flow models did.
Faucets and sinks: drips, cartridges, and finishes
Modern faucets do not use washers — they use cartridges, and a drip after shutoff almost always means a worn cartridge or seal. Older two-handle faucets use washers and seats, which we still service. For visible installs, matching the finish matters as much as the mechanics: a chrome cartridge in a brushed-nickel faucet is a detail we get right.
Worn flapper or misadjusted fill valve — usually a quick, inexpensive repair.
Worn cartridge or seal. Modern faucets use cartridges, not washers.
Failed wax ring or damaged flange — fix it before the floor rots.
Worn pressure-balance cartridge in the shower valve is the first suspect.
Valve wear or mineral buildup — repairable until the body itself is corroded.
Porcelain cracks and deep stains do not repair — replacement is the fix.
Showers and tubs: valves, heads, and diverters
Shower problems split into three parts: the valve behind the wall, the head you see, and the diverter that sends water to the tub spout or the shower. A shower that goes hot and cold when someone flushes has a worn pressure-balance cartridge. A diverter that will not fully switch leaves you showering at half pressure. Heads are the easy win — a new head fixes weak spray in minutes, while valve work is the job to call us for.
Repair or replace? The honest test
Three questions decide it: how old is the fixture, are parts still available, and does the repair cost approach the price of new? If a fixture is on its third repair, replacement usually wins — and the new one brings water savings with it. If it is one worn part in an otherwise sound fixture, repair wins, and we will say so even though replacement pays better.
| Job | Notes |
|---|---|
| Toilet repair | Flapper, fill valve, flush valve, and running-toilet diagnosis |
| Toilet replacement | Old, cracked, or chronically clogging toilets, including low-flow upgrades |
| Faucet repair | Cartridge, seal, and washer replacement on kitchen and bath faucets |
| Faucet and sink installation | New faucets, sinks, and supply connections, finish-matched |
| Shower valve repair and replacement | Pressure-balance and thermostatic cartridges, valve bodies |
| Shower head and tub spout | Head replacement, diverter repair, spout replacement |
| Low-flow fixture upgrades | Toilets, faucets, and shower heads that cut water use without weak performance |
Scope depends on the fixture, parts availability, and whether supply or drain connections need updating — confirmed with a written quote before work begins.
Customer-supplied fixtures welcome
Bought the faucet or toilet yourself? We install customer-supplied fixtures as well as ones we supply. Either way you get a written quote before work starts, and we will flag fit or compatibility problems before opening anything — a fixture that does not match your rough-in is a problem to catch before install day, not during it.
Remodeling a bathroom or kitchen?
Fixture work is part of every remodel. See remodel plumbing.
Is it a leak or a drip?
Hidden leaks waste more than drips do. See leak detection if water is showing up where it should not.
High pressure kills cartridges
Pressure over 80 PSI wears out fixture cartridges years early. See pressure regulators.
Last updated: November 2026
November-December in Lake Stevens
Guests are what make fixture problems urgent in November and December. A running toilet wastes about 200 gallons a day, and it gets noticed when the water bill jumps or when guests use the bathroom over Thanksgiving and Christmas. Cold makes flappers and seals stiff, so a toilet that cycles for 20 seconds every hour has a fill valve or flapper about to fail outright.
The other seasonal fixture is the hose bibb - the freeze item. A hose left attached traps water, and the split happens inside the wall, found only on thaw. Shower valves that will not hold temperature also show up with guests, when two showers and a dishwasher run at once. Fix the running toilet and the dripping faucet before the house fills up, not after.
Our winter plumbing guide for November-December 2026 has the full timeline, the ranked top 10 pain points, and the winterization checklist.
Frequently asked questions
Why does my toilet keep running?
Usually a worn flapper letting water leak from tank to bowl, or a fill valve set too high. Both are inexpensive repairs. If the toilet is also rocking or leaking at the base, that is a wax ring or flange problem — fix it promptly, because a slow base leak rots the floor.
Can a dripping faucet always be repaired?
Almost always, with a cartridge or seal replacement. Modern faucets use cartridges; older two-handle faucets use washers and seats. If the faucet body itself is corroded or the finish is failing, replacement is the better spend.
Should I replace my old toilet with a low-flow model?
If your toilet is a pre-1994 model using 3.5 gallons or more per flush, a modern 1.28-gallon toilet cuts water use substantially and flushes better than the early low-flow models did. If your current toilet works well, there is no urgency.
Do I need to buy the fixture before you come?
No. We supply standard fixtures, or we install one you have already bought. Either way you get a written quote before work starts.
Why does my shower go hot and cold?
Usually a worn pressure-balance or thermostatic cartridge in the shower valve. When someone flushes a toilet or runs a faucet, the valve should hold temperature steady — when it cannot, the cartridge is the first suspect.
What fixture problems show up first when guests arrive?
Running toilets, dripping faucets, and shower valves that will not hold temperature. A toilet that cycles for 20 seconds every hour has a fill valve or flapper about to fail, and a shower that goes hot and cold when someone flushes has a worn pressure-balance cartridge. Fix them before Thanksgiving, not during it.
Why does my toilet cycle for 20 seconds every hour?
Usually a worn flapper letting water leak from tank to bowl, or a fill valve set too high - and cold weather makes flappers and seals stiffer, so a marginal one fails in November. A toilet that cycles every hour is about to fail outright, and a running toilet wastes about 200 gallons a day.
Can't find your question? Browse all plumbing FAQs.
Need a plumber in Lake Stevens, WA?
Call Eby Plumbing for same-day service across Lake Stevens and surrounding areas.
Call (425) 380-0034
